UPLIFT 800 DESK ASSEMBLY INSTRUCTIONS

UPLIFT 800 DESK ASSEMBLY INSTRUCTIONS Parts: 1. 2. 3. 4. 5. 6. 7. 8. 9.

(2) Legs (2) Feet (2) Support beams (1) Control panel (1) Up/Down keypad (1) Power cable (8) 25mm Screws (8) 10mm Screws (20) Wood screws

Tools needed: 1. Drill 2. Philips head driver bit 3. Drill bit 4. Allen wrench (included)

1. Attach the feet to the legs shown in the picture below using the M8 x 25mm w/ Allen wrench

2. Attach the support beams on each side of the legs using the smaller screws w/ Allen wrench

3. Place desktop on soft surface, top side down. Place legs w/ support beams in the center of the top with the feet facing up. Pre-drill the holes using the drill bit then use wood screws to fix legs to the top. NOTE: use a ruler or measuring to tape to ensure proper placement

4. Now place your control panel in desired position as well as the up/down keypad. Connect the leg and keypad cables to corresponding inputs on the control panel. NOTE* ENSURE BOTH LEG CABLES ARE PLUGGED IN BEFORE CONNECTING POWER. THE CONTROL PANEL WILL ONLY RECOGNIZE THE NUMBER OF LEGS ATTATCHED WHEN POWER IS CONNECTED, AND CANNOT BE RESET UNLESS RETURNED TO THE MANUFACTURER!!!

5. Cable management clips are also included in your base package. Use them to clean up hanging wires to avoid interference with legs when raising/lowering desk. 6. Flip the desk top side up, and plug in power. Hold the ↓button on the keypad for about 5 second to reset legs to ensure proper height.

Standard Keypad instructions: Function up and down: Press and hold the desktop up key for moving the desktop upwards, releasing the key when the required desktop height is reached. Press and hold the down key to move the desktop downwards, releasing the key when the required height is reached. It will automatically stop 1 ½” above the lowest height for safety reasons. Release the key then press the key again to move to a lower height. Cabinet- and Shelf-Stop positions: These 2 features can be used to set a lower (cabinet) and upper (shelf) stop that is different than the stops the table is delivered with from the factory. A cabinet stop position can be defined in the lower half of the height range and a shelf stop position in the upper half. If a cabinet stop position is set, this position will be the new lower limit position. If a shelf stop position is set, this position will be the new upper limit position. To store a cabinet stop / shelf stop position, use the following instructions: Press the desktop up key and desktop down key simultaneously for about 1 second. Immediately press and hold the desktop up key for at least 5 sec. (max. 10 sec.) until a double click can be heard. Release the key and the stop is set. Please note that during a Reset (see top of page) the table will not stop at a Cabinet-Stop position! Remove any obstacles below. To deactivate the Cabinet-Stop / Shelf-Stop position go on as shown below: Move the desktop to any position in the lower half to deactivate the cabinet-stop. Move the desktop to any position in the upper half to deactivate the shelf-stop. Press the desktop up key and desktop down key simultaneously for about 1 second. Immediately press and hold the desktop down key at least 5 sec. (max. 10 sec.) until a single click can be heard. Release the key and the stop is deactivated. Repeat in both upper and lower half of range to deactivate both stops.

Memory Keypad Instructions: Saving a desktop position to a memory button: Adjust the desktop to the position you want to save. The display will show the desktop height (e.g. 73cm). Press the memory key until the display reads S –. Press the required position key (e.g. 2), the display will read S 2. The set desktop position will now be saved to the selected position key. You will hear an audible double click and after about 2 seconds the saved desktop height will be displayed. To return to this height at any time, press and hold the position key until the desktop stops moving. If the key is released, movement will stop. Key Lock: With the key lock function, the control unit can be protected from accidental inputs to the keypad. To lock or unlock the keypad, the following steps are necessary: Press the memory key. Press the desktop down button on the left side of the key pad immediately afterwards. If the key lock was inactive, it will

now be activated. If the key lock was active, it will now be deactivated. When the key lock is active, the control unit will sound a slow double click when the up or down key is pressed. Change the displayed desktop position (cm or inch): With this function it is possible to change the displayed desktop position from centimeters to inches or the other way around. The desktop position itself is not affected by this function. Press the position keys 1 & 2 and desktop up at the same time until the display reads S and any number (for instance S 1). Press the desktop up key until the display reads S 5. Press the memory key. If the display was set to centimeters, it will be changed to inches now. If the display was set to inches, it will be changed to centimeters now. The Uplift 800 Sit-Stand Desk only available from …

800-531-3746 TheHumanSolution.com